![]() ![]() Fill in the bottom row with your actual name, the actual date, scale, drawing number, and sheet number.Use the MOVE and ORTHO commands to make the job easier. See the figures below for approximate text heights. You can pick a text height to use that looks pleasing to your eye. Use a text height that matches the area being filling.Set layer Titleblock Text as the current layer.Set Titleblock as the current text style. ![]() When filling in the titleblock in the workalongs and lab exercises in the AutoCAD 2D book, use the following standards: (Figure Step 5) Figure Step 5 AutoCAD book Standards: Filling in the Titleblock Trim the circle you drew in Step 4 and turn layer Construction off. Its center is the intersection of the offset line and the circle. ![]() (Figure Step 3) Figure Step 3 Step 4ĭraw the circle with a radius of 1.5. Draw a circle with the radius of 1.5 units with its center at the point where the arc ends. Offset the line which is tangent to the arc at a distance of 1.5 units.1.5 is the radius of the arc being inserted. (Figure Step 1) Figure Step 1 Step 2ĭraw the construction lines. It must be drawn as an arc as follows: Step 1 When an arc must be constructed that has one end tangent to a line and other end going through a point, you cannot use the FILLET command. Use the COPYBASE command with 0,0 as the base point and use the same coordinates when pasting it into the new drawing. ![]() When copying objects from one drawing to another, the objects must be in the exact location as they were in the original drawing. MUST KNOW: The COPYBASE command is very important to the AutoCAD Operator who works in disciplines such as mapping and architectural. (Select all objects using a crossing window.)Ĭommand: Figure Step 14A Figure Step 14B Figure Step 14C Step 15ĭelete the line in the center by picking it and pressing the Delete key. (Figure Step 13) Figure Step 13 Step 14Įnter the COPY command, as shown below, to copy all objects. Specify second point or : Figure Step 12A Figure Step 12B Step 13įreeze layer: Construction. Step 12Įnter the MOVE command, as shown below, to move all the circles and hexagons 0.5 inches in the positive X direction. Specify second point or : second point is set 4 inches in the positive X direction.)ĪUTHOR’S COMMENTS: I used the base point 0,0. Select objects: Specify opposite corner: 35 found (Snap to the intersection of the construction lines)Ĭommand: Figure Step 10A Figure Step 10B Figure Step 10C Figure Step 10D Step 11Įnter the COPY command, as shown below, to copy all circles and hexagons 4 inches in the positive X direction. (Snap to the intersection of the lines for the base point) (Figure Step 9) Figure Step 9 Step 10Įnter the COPY command, as shown below, to copy the circle and hexagon 4 times. Change the layer of the line you just created to layer: Construction. Using the OFFSET command, offset the left line of the rectangle 1.5 inches to the right. Using these principles in the your day-to-day work will noticeably increase your productivity.ĪUTHOR’S COMMENTS: There should be a total of 9 construction lines, 1 inch apart. If an object has to be drawn that is similar to one that was previously drawn, simply copy it and change it. In AutoCAD, objects only have to be drawn once and then they can be used over and over again even if they are in a different drawing or at a different size or orientation. Using the MOVE and COPY commands are a big part of that productivity. One of the real benefits of using a CAD program is increasing your design and drawing productivity. Fill out titleblocks in Paper space using the AutoCAD 2D book Standards.Describe how to construct a tangent arc that has one end tangent to a line and other end going through a point.Apply the FILETAB and FILETABCLOSE commands to enable the display of the open drawing file tabs above the Graphic window.Apply the MOVE, COPY, COPYCLIP, PASTECLIP, and COPYBASE commands to move and copy objects in the current drawing plus copy objects from one drawing to another.Describe how to move and copy objects in the current drawing and from one drawing to another.When you have completed this module, you will be able to: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |